ABB Relion 650 Series REL650 страница 15 Скачать руководство пользователя

Страница: 15 / 176

Verifying the settings..................................................................131
Completing the test.....................................................................131

Scheme communication logic for residual overcurrent

protection ECPSCH (85).................................................................131

Testing the directional comparison logic function.......................132
Completing the test.....................................................................133

Current reversal and weak-end infeed logic for residual

overcurrent protection ECRWPSCH (85)........................................134

Testing the current reversal logic...............................................134
Testing the weak-end infeed logic..............................................134
Completing the test.....................................................................136

Testing logic functions..........................................................................136

Tripping logic, common 3-phase output SMPPTRC (94)................136

Three-phase operating mode.....................................................137
Circuit breaker lockout................................................................137
Completing the test.....................................................................137

Tripping logic phase segregated output SPTPTRC (94).................138

1p/3p operating mode.................................................................138
Circuit breaker lockout................................................................139
Completing the test.....................................................................139

Testing monitoring functions.................................................................140

Event counter CNTGGIO.................................................................140
Fault locator LMBRFLO...................................................................140

Measuring the operate limit........................................................141
Completing the test.....................................................................142

Testing metering functions....................................................................142

Pulse counter PCGGIO...................................................................142

Exit test mode.......................................................................................142

Section 7 Commissioning and maintenance of the fault

clearing system.................................................................143

Commissioning and maintenance of the fault clearing system.............143

Commissioning tests........................................................................143
Periodic maintenance tests.............................................................143

Visual inspection.........................................................................144
Maintenance tests......................................................................144

Section 8 Troubleshooting ................................................................149

Fault tracing..........................................................................................149

Identifying hardware errors..............................................................149
Identifying runtime errors.................................................................149

Table of contents

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды