ABB Relion 650 Series REL650 Скачать руководство пользователя страница 142

Страница: 142 / 176

6.9.6

Current reversal and weak-end infeed logic for residual

overcurrent protection ECRWPSCH (85)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for ECRWPSCH (85) are available on the local HMI
under

Main menu/Tests/Function status/Scheme communication/ECRWPSCH(85)/

1:ECRWPSCH

. The Signal Monitoring in PCM600 shows the same signals that are

available on the local HMI.

First, test the four step residual overcurrent protection function EF4PTOC (51N/67N)
and then the current reversal and weak-end infeed logic according to the corresponding
instructions. Then continue with the instructions below.

6.9.6.1

Testing the current reversal logic

Inject the polarizing voltage 3V0 to 5% of

VBase

and the phase angle between

voltage and current to 155°, the current leading the voltage.

Inject current (

180° — AngleRCA

) in one phase to about 110% of the set

operating current of the four step residual overcurrent protection (

INDir

Check that the IRVL output is activated in the disturbance recorder after the set
time (

tPickUpRev

Abruptly reverse the current to

AngleRCA

setting lagging the voltage, to operate

the forward directional element.

Check that the IRVL output still is activated after the reversal with a time delay
that complies with the setting (

tDelayRev

Switch off the polarizing voltage and the current.

6.9.6.2

Testing the weak-end infeed logic

If setting

WEI = Echo

Inject the polarizing voltage 3V0 to (180° —

AngleRCA

) of

VBase

and the phase

angle between voltage and current to 155°, the current leading the voltage.

Inject current (180° —

AngleRCA

) in one phase to about 110% of the setting

operating current (

INDir

Activate the CRL binary input.

Section 6

1MRK 506 331-UUS A

Testing functionality

134

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию, Страница: 142 / 176

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы: