ABB Relion 650 Series REL650 страница 75 Скачать руководство пользователя | Manualshive

Страница: 75 / 176

background image

6.4.5.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Current/EFPIOC(50N,IN>>)/1:EFPIOC

for the function, or

for each individual function in a chain, to be tested next. Remember to set the
parameter

Blocked

to

Yes

, for each individual function that has been tested.

6.4.6

Four step residual overcurrent protection, zero or negative

sequence direction EF4PTOC (51N/67N)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

.

Values of the logical signals for EF4PTOC (51N67N) are available on the local HMI
under

Main menu/Tests/Function status/Current/EF4PTOC(51N67N,4IN>)/

X:EF4PTOC

. The Signal Monitoring in PCM600 shows the same signals that are

available on the local HMI.

6.4.6.1

Four step directional residual overcurrent protection

1.

Connect the test set for single current injection to the appropriate IED terminals.
Connect the injection current and voltage to terminals A and neutral.

2.

Set the injected polarizing voltage slightly larger than the set minimum polarizing
voltage (default 1% of Vn) and set the injection current to lag the voltage by an
angle equal to the set reference characteristic angle (

AngleRCA

), if the forward

directional function is selected.
If reverse directional function is selected, set the injection current to lag the
polarizing voltage by an angle equal to RCA+ 180°.

3.

Increase the injected current and note the value at which the studied step of the
function operates.

4.

Decrease the current slowly and note the reset value.

5.

If the test has been performed by injection of current in phase A, repeat the test,
injecting current into terminals B and C with a polarizing voltage connected to
terminals B, respectively C.

6.

Block lower set steps when testing higher set steps according to the instructions
that follow.

7.

Connect a trip output contact to a timer.

8.

Set the injected current to 200% of the operate level of the tested step, switch on
the current and check the time delay.

1MRK 506 331-UUS A

Section 6

Testing functionality

67

Commissioning Manual

«
...
73
74
75
76
77
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Бренд: THOMSON Страницы: 2

Бренд: Respirex Страницы: 12

Бренд: ABB Страницы: 68

Бренд: Zenith Страницы: 54

Бренд: Sony Страницы: 158

Бренд: Sony Страницы: 39

Бренд: Sony Страницы: 35

SIPROTEC 4 7UT6 Series

Бренд: Siemens Страницы: 684

Бренд: Sim2 Страницы: 21

Бренд: Sim2 Страницы: 40

MEGAPOD SA17-SK

Бренд: SK Страницы: 8

Бренд: LeakSmart Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды