ABB Relion 650 Series REL650 страница 119 Скачать руководство пользователя

Страница: 119 / 176

Verify the settings

AutoEnerg

ManEnerg

to be

DBLL

Apply a single-phase voltage of 30%

GblBaseSelBus

to the V-Bus and a single-

phase voltage of 100%

GblBaseSelLine

to the V-Line.

Check that the AUTOENOK and MANENOK outputs are activated after set

tAutoEnerg

respectively

tManEnerg

Decrease the V-Line to 60%

GblBaseSelLine

and keep the V-Bus equal to 30%

GblBaseSelBus

. The outputs should not be activated.

The test can be repeated with different values on the V-Bus and the V-Line.

Testing both directions (DLLB or DBLL)

Verify the local HMI settings

AutoEnerg

ManEnerg

to be

Both

Apply a single-phase voltage of 30%

GblBaseSelLine

to the V-Line and a single-

phase voltage of 100%

GblBaseSelBus

to the V-Bus.

Check that the AUTOENOK and MANENOK outputs are activated after set

tAutoEnerg

respectively

tManEnerg

Change the connection so that the V-Line is equal to100%

GblBaseSelLine

and

the V-Bus is equal to 30%

GblBaseSelBus

. The outputs should still be activated.

The test can be repeated with different values on the V-Bus and the V-Line.

Testing the dead bus dead line (DBDL)

The test should verify that the energizing check function operates for a low voltage on
both the V-Bus and the V-Line, that is, closing of the breaker in a non-energized
system. Test is valid only when this function is used.

Verify the local HMI setting

AutoEnerg

to be

Disabled

and

ManEnerg

to be

DBLL

Set the parameter

ManEnergDBDL

Enabled

Apply a single-phase voltage of 30%

GblBaseSelBus

to the V-Bus and a single-

phase voltage of 30%

GblBaseSelLine

to the V-Line.

Check that the MANENOK output is activated after set

tManEnerg

Increase the V-Bus to 80%

GblBaseSelBus

and keep the V-Line equal to 30%

GblBaseSelLine

. The outputs should not be activated.

Repeat the test with

ManEnerg

set to

DLLB

with different values on the V-Bus

and the V-Line voltage.

6.8.1.4

Testing the voltage selection

1MRK 506 331-UUS A

Section 6

Testing functionality

111

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды