ABB Relion 650 Series REL650 Скачать руководство пользователя | Manualshive

Страница: 110 / 176

background image

•

The BLKV and BLKZ signals appear without any time delay. The BLKZ
signal will be activated only if the internal deadline detection is not
activated at the same time.

•

3PH should appear after 5 seconds, if the remaining voltage levels are lower
than the set

VDLDPU

of the DLD function.

3.

Apply normal conditions as in step

.

The BLKV, BLKZ and 3PH signals should reset, if activated, see step

4.

Change the voltages in all three phases simultaneously.
The voltage change must be greater than the set value for

DVPU

and the current

constant above the set value for

DIPU

.

The BLKV, BLKZ and 3PH signals should not appear.

5.

Repeat step

.

6.

Connect the nominal voltages in all three phases and feed a current below the
operate level in all three phases.

7.

Keep the current constant. Disconnect the voltage in all three phases simultaneously.

8.

To test the internal signals

ifDeltaU

and

ifDeltaI

, change the magnitude of the

voltage and current for phase 1 to a value greater than the set value for

DVPU

and

DIPU

.

9.

Check that the start output signals STDUL1 and STDIL1 and the general start
signals STDU or STDI are activated.

10. Check that the start output signals for the current and voltage phases 2 and 3 are

activated by changing the magnitude of the voltage and current for phases 2 and 3.

6.7.2.5

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Secondary system supervision/SDDRFUF/1:SDDRFUF

for

the function, or for each individual function in a chain, to be tested next. Remember to
set the parameter

Blocked

to

Yes

, for each individual function that has been tested.

6.8

Testing control functions

During periods of frequent counter state/value changes, if the auxiliary
power to the IED is interrupted, it is possible that this information will
be lost.

Section 6

1MRK 506 331-UUS A

Testing functionality

102

Commissioning Manual

«
...
108
109
110
111
112
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Sepam series 20

Бренд: Merlin Gerin Страницы: 10

4003 000 001 DSH42

Бренд: Kindermann Страницы: 2

Бренд: Sim2 Страницы: 12

Sayfline 7603000

Бренд: DBI SALA Страницы: 16

Бренд: Protecta Страницы: 49

Бренд: SPM Страницы: 30

Бренд: Hailo Страницы: 14

Бренд: Kask Страницы: 64

Бренд: Max-Air Systems Страницы: 4

REL 551 2.3 Series

Бренд: ABB Страницы: 140

Бренд: ABB Страницы: 196

Бренд: ABB Страницы: 44

Бренд: GE Страницы: 76

Multilin 3 Series

Бренд: GE Страницы: 74

Бренд: GE Страницы: 129

Бренд: ABB Страницы: 44

Бренд: Magnavox Страницы: 44

50ML8205D - 50" Hd Dlp™ Projection Tv

Бренд: Magnavox Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды