ABB Relion 650 Series REL650 Скачать руководство пользователя | Manualshive

Страница: 107 / 176

background image

The Current circuit supervision function CCSRDIF (87) is conveniently tested with the
same three-phase test set as used when testing the measuring functions in the IED.

The condition for this procedure is that the setting of

IMinOp

is lower than the setting

of

Pickup_Block

.

6.7.1.1

Verifying the settings

1.

Check the input circuits and the operate value of the

IMinOp

current level

detector by injecting current, one phase at a time.

2.

Check the phase current blocking function for all three phases by injecting
current, one phase at a time. The output signals shall reset with a delay of 1
second when the current exceeds 1.5 ·

IBase

.

3.

Inject a current 0.1 ·

IBase

to the reference current input IREFSMPL.

4.

Increase slowly the current in one of the phases current input and check that
FAIL output is obtained when the current is about 0.9 ·

IBase

.

6.7.1.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Secondary system supervision/CCSRDIF(87,INd)/
X:CCSRDIF

for the function, or for each individual function in a chain, to be tested

next. Remember to set the parameter

Blocked

to

Yes

, for each individual function that

has been tested.

6.7.2

Fuse failure supervision SDDRFUF

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

.

Values of the logical signals for SDDRFUF are available on the local HMI under

Main

menu/Tests/Function status/Secondary system supervision/SDDRFUF/
1:SDDRFUF

. The Signal Monitoring in PCM600 shows the same signals that are

available on the local HMI.

The verification is divided in two main parts. The first part is common to all fuse
failure supervision options, and checks that binary inputs and outputs operate as
expected according to actual configuration. In the second part the relevant set operate
values are measured.

1MRK 506 331-UUS A

Section 6

Testing functionality

99

Commissioning Manual

«
...
105
106
107
108
109
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

3M Flexiguard M200

Бренд: DBI SALA Страницы: 82

Бренд: Silverline Страницы: 2

Бренд: Magnavox Страницы: 60

Бренд: Datalogic Страницы: 10

Бренд: Crye Precision Страницы: 28

Бренд: Samsung Страницы: 64

Бренд: Samsung Страницы: 72

Бренд: ABB Страницы: 24

Бренд: Panasonic Страницы: 18

EP7 Sonic Defenders Ultra

Бренд: Superfire Страницы: 2

ICY BOX IB-AC620-M2

Бренд: RaidSonic Technology Страницы: 10

PT50DL54 - 50" DLP TV

Бренд: Panasonic Страницы: 112

Бренд: Rohm Страницы: 14

Бренд: Mitsubishi Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды