ABB Relion 650 Series REL650 Скачать руководство пользователя | Manualshive

Страница: 120 / 176

background image

Testing the voltage selection for single CB arrangements

This test should verify that the correct voltage is selected for the measurement in the
SESRSYN function used in a double-bus arrangement. Apply a single-phase voltage of
30%

GblBaseSelLine

to the V-Line and a single-phase voltage of 100%

GblBaseSelBus

to the V-Bus.

If the VB1OK or VB2OK inputs for the fuse failure are used, they must be activated,
during tests below. Also verify that deactivation prevents operation and gives an alarm.

1.

Connect the signals above to binary inputs and binary outputs.

2.

Connect the voltage inputs to the analog inputs used for each bus or line
depending of the type of busbar arrangement and verify that correct output
signals are generated.

6.8.1.5

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Control/SESRSYN(25,SYNC)/X:SESRSYN

for the function,

or for each individual function in a chain, to be tested next. Remember to set the
parameter

Blocked

to

Yes

, for each individual function that has been tested.

6.8.2

Autorecloser for 3-phase operation SMBRREC (79)

Verification of the Autorecloser for 3-phase operation function SMBRREC (79) for three-
phase reclosing attempts can be considered to consist of two parts.

•

One part to verify the internal logic and timing of the function

•

One part to verify its interaction with the protection system

This section deals with verification of SMBRREC (79) itself. However, it is practical
to initiate SMBRREC (79) by activating a protection function, for example, by
secondary injection tests.

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for SMBRREC (79) are available on the local HMI under

Main menu/Tests/Function status/Control/SMBRREC(79,0->1)/X:SMBRREC

.

The Signal Monitoring in PCM600 shows the same signals that are available on the
local HMI.

Section 6

1MRK 506 331-UUS A

Testing functionality

112

Commissioning Manual

«
...
118
119
120
121
122
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Бренд: LEADING EDGE SAFETY Страницы: 36

DuraTech 6 Mini

Бренд: Falltech Страницы: 35

Бренд: RCA Страницы: 64

Бренд: ABB Страницы: 68

Бренд: Magnavox Страницы: 32

Бренд: Tapeswitch Страницы: 9

Бренд: Sanyo Страницы: 136

GLOBBER 529-001

Бренд: TEMPLAR Страницы: 68

Бренд: Mitsubishi Страницы: 11

Бренд: Mitsubishi Страницы: 76

Бренд: Mitsubishi Страницы: 107

Бренд: Mitsubishi Страницы: 69

Бренд: Mitsubishi Страницы: 71

Бренд: Mitsubishi Страницы: 103

Бренд: Mitsubishi Страницы: 100

Бренд: Mitsubishi Страницы: 106

LaserVue L65-A90

Бренд: Mitsubishi Страницы: 96

Бренд: Kopp Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды