manualshive.com logo in svg

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Поделиться
Скачать
ABB Relion 650 Series REL650 Скачать руководство пользователя страница 68

1.

Program the test equipment for a single-phase to ground fault and energize
FDPSPDIS (21) and check that the input BLOCK on the power swing detection
function ZMRPSB (68) is activated.

2.

Make a test sequence so that a single-phase to ground fault occurs after that the
trajectory of the impedance has passed the outer and inner boundary of ZMRPSB
(68) during power swing. Use the result from test of ZMRPSB (68) above to
determine when the fault shall be applied. The ground-fault must be activated
before 

tR1

 has elapsed.

3.

Start the sequence and observe that the PICKUP signal will not be activated.

6.3.5.4 

Completing the test

Continue to test another function or end the testing by setting the parameter 

TestMode

to 

Disabled

 under 

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter 

Blocked

 to 

No

 under 

Main menu/Tests/

Function test modes/Impedance/ZMRPSB(68)/1:ZMRPSB

 for the function, or for

each individual function in a chain, to be tested next. Remember to set the parameter

Blocked

 to 

Yes

, for each individual function that has been tested.

6.3.6 

Automatic switch onto fault logic, voltage and current based

ZCVPSOF

Prepare the IED for verification of settings as outlined in 

5.1 "Preparing the IED to

verify settings"

.

Values of the logical signals for ZCVPSOF are available on the local HMI under 

Main

menu/Tests/Function status/Impedance/ZCVPSOF/1:ZCVPSOF

. The Signal

Monitoring in PCM600 shows the same signals that are available on the local HMI.

Automatic switch onto fault logic, voltage and current based function ZCVPSOF is
checked using secondary injection tests together with the Scheme communication logic
for distance or overcurrent protection function ZCPSCH (85) and with the dead line
detection function (DLD), which is embedded in ZCVPSOF. ZCVPSOF is activated
either by the external input BC, or by the internal DLD. SDDRFUF is done with a pre-
fault condition where the phase voltages and currents are at zero. A reverse three-phase
fault with zero impedance and a three-phase fault with an impedance corresponding to
the whole line is applied. This fault shall cause an instantaneous trip and result in a
TRIP indication.

6.3.6.1 

External activation of ZCVPSOF

1.

Activate the switch onto fault BC input.

Section 6

1MRK 506 331-UUS A

Testing functionality

60

Commissioning Manual

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды