ABB Relion 650 Series REL650 Скачать руководство пользователя | Manualshive

Страница: 72 / 176

background image

4.

Increase the injected current and note the operate value of the tested step of the
function.

5.

Decrease the current slowly and note the reset value.

6.

If the test has been performed by injection of current in phase A, repeat the test,
injecting current into phases B and C with polarizing voltage connected to phases
B, respectively C (

1 out of 3

currents for operation).

7.

If the test has been performed by injection of current in phases AB, repeat the
test, injecting current into phases BC and CA with the appropriate phase angle of
injected currents.

8.

Block higher set stages when testing lower set stages by following the procedure
described below.

9.

Connect a trip output contact to a timer.

10. Set the injected current to 200% of the operate level of the tested stage, switch on

the current and check the time delay.
For inverse time curves, check the operate time at a current equal to 110% of the
operate current for

txMin

.

11. Check that all trip and pickup contacts operate according to the configuration

(signal matrixes)

12. Reverse the direction of the injected current and check that the protection does

not operate.

13. Repeat the above described tests for the higher set stages.
14. Finally check that pickup and trip information is stored in the event menu.

Verification of the non-directional phase overcurrent function is
done as instructed above, without applying any polarizing voltage.

6.4.3.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Current/OC4PTOC(51_67,4I>)/1:OC4PTOC

for the function,

or for each individual function in a chain, to be tested next. Remember to set the
parameter

Blocked

to

Yes

, for each individual function that has been tested.

6.4.4

Four step phase overcurrent protection phase segregated

output OC4SPTOC (51_67)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Section 6

1MRK 506 331-UUS A

Testing functionality

64

Commissioning Manual

«
...
70
71
72
73
74
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Бренд: Philips Страницы: 1

Бренд: Dräger Страницы: 28

3M Flexiguard M200

Бренд: DBI SALA Страницы: 82

Бренд: cleanAIR Страницы: 48

RESCUE STICK MRD100

Бренд: Mustang Survival Страницы: 12

Бренд: Mustang Survival Страницы: 24

BugHunter DAudio bda-4 Voice

Бренд: i4Technology Страницы: 6

Бренд: Mustang Survival Страницы: 32

Oven Front Lock

Бренд: Safety 1st Страницы: 3

Бренд: Zenith Страницы: 54

Бренд: Samsung Страницы: 64

Бренд: ABB Страницы: 44

Voltage Guard - 70

Бренд: Cristec Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды