ABB Relion 650 Series REL650 страница 71 Скачать руководство пользователя | Manualshive

Страница: 71 / 176

background image

3. Switch the fault current off. Observe to not exceed the maximum permitted

overloading of the current circuits in the IED.

4. Compare the measured operating current with the set value.

6.4.2.1

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

to

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

to

No

under

Main menu/Tests/

Function test modes/Current/SPTPIOC(50,I>>)/1:SPTPIOC

for the function, or

for each individual function in a chain, to be tested next. Remember to set the
parameter

Blocked

to

Yes

, for each individual function that has been tested.

6.4.3

Four step phase overcurrent protection 3-phase output

OC4PTOC (51_67)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

.

Values of the logical signals for OC4PTOC (51_67) are available on the local HMI
under

Main menu/Tests/Function status/Current/OC4PTOC(51_67,4I>)/

1:OC4PTOC

. The Signal Monitoring in PCM600 shows the same signals that are

available on the local HMI.

6.4.3.1

Verifying the settings

1.

Connect the test set for current injection to the appropriate IED phases.
If there is any configuration logic that is used to enable or block any of the four
available overcurrent steps, make sure that the step under test is enabled (for
example, end fault protection).
Connect the symmetrical three-phase injection current into phases A, B and C.

2.

Connect the test set for the appropriate three-phase voltage injection to the IED
phases A, B and C. The protection shall be fed with a symmetrical three-phase
voltage.

3.

Set the injected polarizing voltage slightly larger than the set minimum polarizing
voltage (default is 5% of

VBase

) and set the injection current to lag the

appropriate voltage by an angle of 55° if forward directional function is selected.
If

1 out of 3

currents for operation is chosen: The voltage angle of phase A is the

reference.
If reverse directional function is selected, set the injection current to lag the
polarizing voltage by an angle equal to 235° (equal to 55° + 180°).

1MRK 506 331-UUS A

Section 6

Testing functionality

63

Commissioning Manual

«
...
69
70
71
72
73
...
»

Содержание Relion 650 Series REL650

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Relion 650 Series REL650

Бренд: Cambium Networks Страницы: 16

Бренд: U-Line Страницы: 2

Бренд: 3M Страницы: 138

Бренд: SafeWaze Страницы: 5

Бренд: Hitachi Страницы: 72

Бренд: Falltech Страницы: 35

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 3

Бренд: Philips Страницы: 2

Бренд: Sony Страницы: 57

Бренд: Sony Страницы: 173

Бренд: TAZ Страницы: 17

High-speed Series

Бренд: TDK Страницы: 25

SHOCK RELAY TSB2CT Series

Бренд: Tsubaki Страницы: 12

Worksafe SSP19F

Бренд: Sealey Страницы: 2

Бренд: Startco Страницы: 47

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды