ABB Relion 650 Series REL650 Скачать руководство пользователя

Страница: 74 / 176

Check of the non-directional phase over-current function. This is done
in principle as instructed above, without applying any polarizing voltage.

6.4.4.2

Completing the test

Continue to test another function or end the testing by setting the parameter

TestMode

Disabled

under

Main menu/Tests/IED test mode/1:TESTMODE

. If another

function is tested, then set the parameter

Blocked

under

Main menu/Tests/

Function test modes/Current/OC4SPTOC(51_67,4I>)/1:OC4SPTOC

for the

function, or for each individual function in a chain, to be tested next. Remember to set
the parameter

Blocked

Yes

, for each individual function that has been tested.

6.4.5

Instantaneous residual overcurrent protection EFPIOC (50N)

Prepare the IED for verification of settings as outlined in

5.1 "Preparing the IED to

verify settings"

Values of the logical signals for EFPIOC (50N) are available on the local HMI under

Main menu/Tests/Function status/Current/EFPIOC(50N,IN>>)/1:EFPIOC

. The

Signal Monitoring in PCM600 shows the same signals that are available on the local HMI.

To verify the settings the following fault type should be tested:

•

Phase-to-ground fault

Ensure that the maximum continuous current, supplied from the current source used for
the test of the IED, does not exceed four times the rated current value of the IED.

6.4.5.1

Measuring the operate limit of set values

Inject a phase current into the IED with an initial value below that of the setting.

Increase the injected current in the Ln or in the neutral (summated current input)
phase until the TRIP signal appears.

Disable the fault current
Observe to not exceed the maximum permitted overloading of the current circuits
in the IED

Compare the measured operating current with the set value.

Section 6

1MRK 506 331-UUS A

Testing functionality

Commissioning Manual

Содержание Relion 650 Series REL650
















































































































































































Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды

ABB Relion 650 Series REL650, Руководство по вводу в эксплуатацию

Результаты поиска

Содержание Relion 650 Series REL650

Отзывы:

Похожие инструкции для Relion 650 Series REL650

Бренды по названию

Популярные бренды