Yealink W80 Administrator'S Manual Download Page 35 | Manualshive

Page: 35 / 260

background image

Administrator’s Guide for W80 DECT IP Multi-Cell System

32

Notes on Configuring IPUI

A few notes you should know when registering handsets using IPUI code:

l

The registration status will not be disabled automatically if you enable it by "handset.X.reg.enable".

l

If you duplicate the IPUI code during the configuration, only the IPUI with the smaller handset number takes
effect.

l

If you configure another IPUI code for another handset but the handset number is the same as an existing one,
the existing IPUI will be overwritten.

l

If you configure the IPUI code for the registered handset, the handset will be unregistered.

l

When the handset is deleted, the handset and its IPUI code will be deleted at the same time.

l

You cannot directly modify the IPUI code via the web user interface. The IPUI code can only be modified via auto
provisioning, or re-entered after deleted via the web user interface.

IPUI Code Configuration

The following table lists the parameters you can use to import the IPUI code.

Parameter

handset.X.reg.enable

[1]

<MAC>.cfg

Description

It enables or disables the registration status for handset X.

Note

: The value of X corresponds to that of "account.X.user_name". When the IPUI code is invalid or

not configured, the registration status cannot be enabled by this parameter.

Permitted
Values

0

-Disabled

1

-Enabled

Default

0

Web UI

Handset & Account > Handset Registration > Add Handset > Start Register Handset

Parameter

handset.X.ipui

[1]

<MAC>.cfg

Description

It configures the IPUI code of handset X.

Note

: The IPUI code is not case sensitive.

Permitted
Values

String within 10 characters (only contain numbers and letters)

Default

Blank

Web UI

Handset & Account > Handset Registration > Add Handset > IPUI

[1]

X is the handset ID. X=1-100.

Related Topics

Obtaining the IPUI Code of the Handset

Handset Registration Center

The registration center allows you to register groups of handsets in one registration process. During this time, the
system will automatically register the handset and assign the corresponding account according to the IPUI code.

You can find the following information from the registration center:

l

Total Handsets

: Shows how many handsets are registered in the current system.

l

Registered Handsets

: Shows how many handsets are registered through the registration center this time

l

Current Time

: Shows the current system time. It is updated in real time.

Topics

«
...
33
34
35
36
37
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 8

KX-TG7622, KX-TG7623, KX-TG762

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 6

Clearspan 6731i

Brand: Aastra Pages: 5

Brand: Aastra Pages: 4

Brand: Aastra Pages: 2

Venture IP Telephone System

Brand: Aastra Pages: 24

Venture IP Telephone System

Brand: Aastra Pages: 43

Brand: Aastra Pages: 2

Brand: Aastra Pages: 72

Brand: Yealink Pages: 2

CIT310 - iPhone Cordless Phone

Brand: Linksys Pages: 2

Brand: Selta Pages: 102

Brand: Uniden Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands