Yealink W80 Administrator'S Manual Download Page 42 | Manualshive

Page: 42 / 260

background image

Account Settings

39

Note

: It works only if "account.X.reg_failed_retry_min_time" and "account.X.reg_failed_retry_max_

time" are set to 0.

Permitted
Values

Integer from 0 to 1800

Default

30

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > SIP Registration Retry Timer
(0~1800s)

Parameter

account.X.reg_failed_retry_min_time

[1]

<MAC>.cfg

Description

It configures the base time to wait (in seconds) for the phone to retry to re-register after the account
registration fails.

Note

: It is used in conjunction with the parameter "account.X.reg_failed_retry_max_time" to determine

how long to wait. The algorithm is defined in RFC 5626. We recommend that you set this value to an
integer between 10 to 120 if needed. If the values of this parameter and the parameter "accoun-
t.X.reg_failed_retry_max_time" are set to 0, the interval configured by "account.X.reg_fail_retry_inter-
val" will be used.

Permitted
Values

Integer greater than or equal to 0

Default

0

Parameter

account.X.reg_failed_retry_max_time

[1]

<MAC>.cfg

Description

It configures the maximum time to wait (in seconds) for the phone to retry to re-register after the
account registration fails.

Note

: It is used in conjunction with the parameter "account.X.reg_failed_retry_min_time" to determine

how long to wait. The algorithm is defined in RFC 5626. We recommend that you set this value to an
integer between 60 to 1800 if needed. If the values of this parameter and the parameter "accoun-
t.X.reg_failed_retry_min_time" are set to 0, the interval configured by "account.X.reg_fail_retry_inter-
val" will be used.

Permitted
Values

Integer greater than or equal to 0

Default

60

[1]

X is the account ID. X=1-100.

[2]

Y is the server ID. Y=1-2.

Registration Settings Configuration

The following table lists the parameters you can use to change the registration settings.

Parameter

account.X.enable_user_equal_phone

[1]

<MAC>.cfg

Description

It enables or disables the phone to add “user=phone” to the SIP header of the INVITE message.

Permitted
Values

0

-Disabled

1

-Enabled

Default

0

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > Send user=phone

Parameter

account.X.register_mac

[1]

<MAC>.cfg

Description

It enables or disables the phone to add MAC address to the SIP header of the REGISTER message.

Permitted

0

-Disabled

«
...
40
41
42
43
44
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: Samsung Pages: 8

Brand: 3Com Pages: 128

Brand: Samsung Pages: 79

Brand: Samsung Pages: 88

Brand: Samsung Pages: 215

Brand: Samsung Pages: 155

Brand: Aastra Pages: 2

Brand: Aastra Pages: 2

Brand: Aastra Pages: 2

Brand: Aastra Pages: 2

Dialog 4106 Basic

Brand: Aastra Pages: 2

Brand: EastLink Pages: 28

Brand: Aastra Pages: 461

Brand: Aastra Pages: 40

Brand: Aastra Pages: 47

Brand: Aastra Pages: 47

Brand: Safeline Pages: 32

Brand: Talkswitch Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands