Yealink W80 Administrator'S Manual Download Page 207 | Manualshive

Page: 207 / 260

background image

Administrator’s Guide for W80 DECT IP Multi-Cell System

204

Call Transfer

Call transfer enables the phones to transfer an existing call to a third party. For example, if party A is in an active call
with party B, party A can transfer this call to party C (the third party). Then, party B will begin a new call with party C,
and party A will disconnect.

Yealink phones support call transfer using the REFER method specified in

and offer three types of trans-

fer:

l

Blind Transfer

-- Transfer a call directly to another party without consulting. Blind transfer is implemented by a

simple REFER method without Replaces in the Refer-To header.

l

Semi-attended Transfer

-- Transfer a call after hearing the ringback tone. The semi-attended transfer is imple-

mented by a REFER method with Replaces in the Refer-To header.

The semi-attended transfer is applicable to that when users do not want to consult with the third party after hear-
ing the ringback tone, and the third party has not answered the call, the users can cancel the transfer or imple-
ment the transfer.

l

Attended Transfer (Consultative Transfer)

-- Transfer a call with prior consulting. Attended transfer is imple-

mented by a REFER method with Replaces in the Refer-To header.

Topic

Call Transfer Configuration

Call Transfer Configuration

The following table lists the parameters you can use to configure call transfer.

Parameter

transfer.semi_attend_tran_enable

<y0000000000xx>.cfg

Description

It enables or disables the semi-attended transfer.

Permitted
Values

0

-Disabled, when the user the TRAN key after hearing the ringback tone, the phone will blind transfer

the call.

1

-Enabled, when the user the TRAN key after hearing the ringback tone, the phone will transfer the

call after the transferee answers the call.

Default

1

Web UI

Features > Transfer > Semi-Attended Transfer

Parameter

account.X.transfer_refer_to_contact_head-
er.enable

[1]

<MAC>.cfg

Description

It enables or disables the Refer-To header to use the information of the Contact header in the second
200 OK message when attended transfer.

Permitted
Values

0

-Disabled

1

-Enabled

Default

0

Parameter

transfer.blind_tran_on_hook_enable

<y0000000000xx>.cfg

Description

It enables or disables the phone to complete the blind transfer through on-hook besides the TRAN
key.

Note

: Blind transfer means transferring a call directly to another party without consulting.

Permitted
Values

0

-Disabled

1

-Enabled

Default

1

«
...
205
206
207
208
209
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: Yealink Pages: 2

Brand: Panasonic Pages: 72

Brand: Gigaset Pages: 26

Brand: Swyx Pages: 4

Brand: Radio Shack Pages: 24

Brand: L-3 Communications Pages: 312

Brand: AT&T Pages: 4

Brand: Witura Pages: 12

Brand: Bell Pages: 11

Brand: GAI-Tronics Pages: 16

Brand: Uniden Pages: 28

Brand: GE Pages: 72

Brand: Makita Pages: 28

Brand: LG Pages: 72

Brand: LG Pages: 30

Brand: LG Pages: 33

Brand: LG Pages: 20

Brand: LG Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands