Yealink W80 Administrator'S Manual Download Page 202 | Manualshive

Page: 202 / 260

background image

Call Features

199

When a call is placed on hold, the phones send an INVITE request with HOLD SDP to request remote parties to
stop sending media and to inform them that they are being held. The phones support two call hold methods, one is

, which sets the “a” (media attribute) in the SDP to sendonly, recvonly or inactive (for example, a=se-

endonly). The other is

, which sets the “c” (connection addresses for the media streams) in the SDP to

zero (for example, c=0.0.0.0).

Topic

Call Hold Configuration

Call Hold Configuration

The following table lists the parameters you can use to configure call hold.

Parameter

sip.rfc2543_hold

<y0000000000xx>.cfg

Description

It enables or disables the phone to use RFC 2543 (c=0.0.0.0) outgoing hold signaling.

Permitted
Values

0

-Disabled, SDP media direction attributes (such as a=sendonly) per RFC 3264 is used when placing

a call on hold.

1

-Enabled, SDP media connection address c=0.0.0.0 per RFC 2543 is used when placing a call on

hold.

Default

0

Web UI

Features > General Information > RFC 2543 Hold

Parameter

account.X.hold_use_inactive

[1]

<MAC>.cfg

Description

It enables or disables the phone to use inactive outgoing hold signaling.

Note

: It works only if “sip.rfc2543_hold" is set to 0 (Disabled).

Permitted
Values

0

-Disabled, SDP media direction attribute “a=sendonly” is used when placing a call on hold.

1

-Enabled, SDP media direction attribute “a=inactive” is used when placing a call on hold. RTP pack-

ets will not be sent or received.

Default

0

[1]

X is the account ID. X=1-100.

Call Forward

You can forward calls in special situations, such as when the phone is busy or there is no answer, or forwarding all
incoming calls to a contact immediately.

Topics

Call Forward Settings Configuration
Call Forward Feature Configuration
Call Forward Synchronization for Server-side Configuration

Call Forward Settings Configuration

You can change the following call forward settings:

l

Enable or disable the call forward feature. If disabled, the users have no permission to configure call forward on
their phone.

l

Allow or disallow users to forward an incoming call to an international telephone number (the prefix is 00).

l

Enable or disable the display of the Diversion header. The Diversion header allows the phone which receives a
forwarded-call to indicate where the call was from.

The following table lists the parameters you can use to change the call forward settings.

«
...
200
201
202
203
204
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: Samsung Pages: 65

Brand: Karel Pages: 45

Brand: Jabra Pages: 7

Brand: Aiwa Pages: 18

Brand: Karel Pages: 20

Brand: 3Com Pages: 130

Auto-Attendant System

Brand: Yosin Pages: 17

Brand: VTech Pages: 51

Bamboo BLP7670-001

Brand: Blaupunkt Pages: 5

Brand: Craftsman Pages: 18

Brand: Sennheiser Pages: 93

Brand: Siemens Pages: 10

Brand: Siemens Pages: 18

Brand: Siemens Pages: 2

Gigaset 4010 Comfort

Brand: Siemens Pages: 28

Gigaset 3000 Comfort

Brand: Siemens Pages: 28

Brand: Siemens Pages: 22

Gigaset 4000 Comfort

Brand: Siemens Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands