Yealink W80 Administrator'S Manual Download Page 94

Page: 94 / 260

Administrator’s Guide for W80 DECT IP Multi-Cell System

Permitted
Values

Integer from 1 to 65535

Default

Web UI

Network > Advanced > Web Server > HTTP Port (1~65535)

Parameter

static.wui.https_enable

[1]

<y0000000000xx>.cfg

Description

It enables or disables to access the web user interface of the phone over a secure tunnel (HTTPS).

Permitted
Values

-Disabled

-Enabled

Default

Web UI

Network > Advanced > Web Server > HTTPS

Parameter

static.network.port.https

[1]

<y0000000000xx>.cfg

Description

It configures the port used to access the web user interface of the phone over a secure tunnel
(HTTPS).

Permitted
Values

Integer from 1 to 65535

Default

443

Web UI

Network > Advanced > Web Server > HTTPS Port (1~65535)

[1]

If you change this parameter, the phone will reboot to make the change take effect.

Central Provisioning

Central provisioning enables you to provision multiple phones from a provisioning server that you set up, and main-
tain a set of boot files, configuration files and resource files for all phones in the central provisioning server.

The following figure shows how the phone interoperates with provisioning server when you use the centralized pro-
visioning method:

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands