Yealink W80 Administrator'S Manual Download Page 56

Page: 56 / 260

Network Configurations

Network Configurations

You can make custom network configurations.

Topics

IPv4 Network Settings
DHCP Option for IPv4
VLAN
Real-Time Transport Protocol (RTP) Ports
Network Address Translation (NAT)
VPN
Quality of Service (QoS)
802.1x Authentication
TR-069 Device Management

IPv4 Network Settings

You can configure the devices to operate in IPv4 mode.

After establishing network connectivity, the devices obtain the IPv4 network settings from a Dynamic Host Con-
figuration Protocol (DHCPv4) server.

You can also configure IPv4 network settings manually.

Note

: Yealink devices comply with the DHCPv4 specifications documented in

RFC 2131

, and ICMPv6 specifications doc-

umented in

RFC 4443

Topics

IPv4 Configuration

IPv4 Configuration

The following table lists the parameters you can use to configure IPv4.

Parameter

static.network.internet_port.type

[1]

<y0000000000xx>.cfg

Description

It configures the Internet port type for IPv4.

Permitted
Values

-DHCP

-Static IP

Default

Web UI

Network > Basic > IPv4 Config > Configuration Type

Parameter

static.network.internet_port.ip

[1]

<y0000000000xx>.cfg

Description

It configures the IPv4 address.

Note

: It works only if "static.network.internet_port.type" is set to 2 (Static IP).

Permitted
Values

IPv4 Address

Default

Blank

Web UI

Network > Basic > IPv4 Config > Configuration Type (Static IP) > IP Address

Parameter

static.network.internet_port.mask

[1]

<y0000000000xx>.cfg

Description

It configures the IPv4 subnet mask.

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands