Yealink W80 Administrator'S Manual Download Page 100 | Manualshive

Page: 100 / 260

background image

Administrator’s Guide for W80 DECT IP Multi-Cell System

97

Default

1

Parameter

static.auto_provision.dns_resolv_nretry

<y0000000000xx>.cfg

Description

It configures the retry times when the phone fails to resolve the access URL of the provisioning server.

Note

: For each different DNS server, it works only if “static.auto_provision.dns_resolv_nosys" is set to

1 (Enabled).

Permitted
Values

Integer from 1 to 10

Default

2

Parameter

static.auto_provision.dns_resolv_timeout

<y0000000000xx>.cfg

Description

It configures the timeout (in seconds) for the phone to retry to resolve the access URL of the pro-
visioning server.

Note

: For each different DNS server, it works only if “static.auto_provision.dns_resolv_nosys" is set to

1 (Enabled).

Permitted
Values

Integer from 1 to 60

Default

5

[1]

If you change this parameter, the phone will reboot to make the change take effect.

Setting Up a Provisioning Server

You can use a provisioning server to configure your phones. A provisioning server allows for flexibility in upgrading,
maintaining and configuring the phone. Boot files, configuration files, and resource files are normally located on this
server.

Topics

Supported Provisioning Protocols
Supported Provisioning Server Discovery Methods
Configuring a Provisioning Server

Supported Provisioning Protocols

Yealink phones support several transport protocols for provisioning:

l

Trivial File Transfer Protocol (TFTP)

l

File Transfer Protocol (FTP)

l

Hyper Text Transfer Protocol – Secure (HTTPS)

l

File Transfer Protocol – Secure (FTPS)

Note

: There are two types of FTP methods—active and passive. The phones are not compatible with active FTP.

You can specify the transport protocol in the provisioning server address, for example, http://xxxxxxx. If not spe-
cified, the TFTP protocol is used.

Topic

Provisioning Protocols Configuration

Provisioning Protocols Configuration

The following table lists the parameter you can use to configure provisioning protocols.

Parameter

static.auto_provision.server.type

<y0000000000xx>.cfg

Description

It configures the protocol the phone uses to connect to the provisioning server.

«
...
98
99
100
101
102
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: Octopus Pages: 128

Brand: Premier Pages: 12

Brand: Binatone Pages: 2

Brand: ETS Pages: 2

Brand: Radio Shack Pages: 20

Polycom VVX 310

Brand: EarthLink Pages: 4

Brand: RTX Pages: 12

Brand: Sanyo Pages: 38

Brand: Cisco Pages: 202

Brand: LG Pages: 37

Brand: LG Pages: 54

Brand: LG Pages: 47

Brand: LG Pages: 30

Brand: LG Pages: 14

Brand: LG Pages: 76

Brand: LG Pages: 58

Brand: LG Pages: 175

Brand: LG Pages: 113

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands