Yealink W80 Administrator'S Manual Download Page 203

Page: 203 / 260

Administrator’s Guide for W80 DECT IP Multi-Cell System

200

Parameter

features.fwd.allow

<y0000000000xx>.cfg

Description

It enables or disables the call forward feature.

Permitted
Values

-Disabled, call forward feature is not available to the users.

-Enabled

Default

Parameter

forward.international.enable

<y0000000000xx>.cfg

Description

It enables or disables the phone to forward incoming calls to international numbers (the prefix is 00).

Permitted
Values

-Disabled

-Enabled

Default

Web UI

Features > General Information > Fwd International

Parameter

features.fwd_diversion_enable

<y0000000000xx>.cfg

Description

It enables or disables the phone to present the diversion information when an incoming call is for-
warded to the IP phone.

Permitted
Values

-Disabled

-Enabled, the server can use the Diversion field with a SIP header to inform the phone of a call’s his-

tory.

Default

Web UI

Features > General Information > Diversion/History-Info

Call Forward Feature Configuration

Yealink phones support call forward on code and off code to activate and deactivate server-side call forward fea-
ture. They may vary on different servers.

Topic

Call Forward Configuration

The following table lists the parameters you can use to configure call forward.

Parameter

account.X.always_fwd.enable

[1]

<MAC>.cfg

Description

It triggers always forward feature to on or off.

Note:

It works only if “features.fwd.allow” is set to 1 (Enabled) and “features.fwd_mode” is set to 1

(Custom).

Permitted
Values

-Off

-On, incoming calls to the account X are forwarded to the destination number (configured by the para-

meter “account.X.always_fwd.target”) immediately.

Default

Web UI

Features > Forward&DND > Forward > AccountX > Always Forward > On/Off

Parameter

account.X.always_fwd.target

[1]

<MAC>.cfg

Description

It configures the destination number of the always forward.

Note:

It works only if “features.fwd.allow” is set to 1 (Enabled) and “features.fwd_mode” is set to 1

(Custom).

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands