Yealink W80 Administrator'S Manual Download Page 193

Page: 193 / 260

Administrator’s Guide for W80 DECT IP Multi-Cell System

190

CUSTOM

-The custom outbound identity configured by “dialplan.emergency.custom_asserted_id” will

be used; if “dialplan.emergency.custom_asserted_id” is left blank, the LLDP-MED ELIN value will be
used.

Default

ELIN

Parameter

dialplan.emergency.custom_asserted_id

<y0000000000xx>.cfg

Description

It configures the custom outbound identity when placing an emergency call.

Note

: It works only if “dialplan.emergency.enable” is set to 1 (Enabled).

Permitted
Values

A number with 10 to 25 digits

- for example, 1234567890. The SIP URI constructed from the number

and SIP server (for example, abc.com) is included in the P-Asserted-Identity (PAI) header (for
example, <sip:[email protected] > ).

SIP URI

- for example, sip:[email protected]. The full URI is included in the P-Asserted-Iden-

tity (PAI) header and the address will be replaced by the emergency server (for example,
<sip:[email protected] > ).

TEL URI

- for example, tel:+16045558000. The full URI is included in the P-Asserted-Identity (PAI)

header (for example, <tel:+16045558000 > ).

Default

Blank

Parameter

dialplan.emergency.server.X.address

[1]

<y0000000000xx>.cfg

Description

It configures the IP address or domain name of the emergency server X to be used for routing calls.

Note

: If the account information has been configured (no matter whether the account registration suc-

ceeds or fails), the emergency calls will be dialed using the following priority: SIP server > emergency
server; if not, the emergency server will be used. It works only if “dialplan.emergency.enable” is set to
1 (Enabled).

Permitted
Values

IP address or domain name

Default

Blank

Parameter

dialplan.emergency.server.X.port

[1]

<y0000000000xx>.cfg

Description

It configures the port of emergency server X to be used for routing calls.

Note

: It works only if “dialplan.emergency.enable” is set to 1 (Enabled).

Permitted
Values

Integer from 0 to 65535

Default

5060

Parameter

dialplan.emergency.server.X.transport_type

[1]

<y0000000000xx>.cfg

Description

It configures the transport protocol the phones use to communicate with the emergency server X.

Note

: It works only if “dialplan.emergency.enable” is set to 1 (Enabled).

Permitted
Values

-UDP

-TCP

-TLS

-DNS-NAPTR

Default

Parameter

dialplan.emergency.X.value

[2]

<y0000000000xx>.cfg

Description

It configures the emergency number to use on your phones so a caller can contact emergency ser-
vices in the local area when required.

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands