Yealink W80 Administrator'S Manual Download Page 170

Page: 170 / 260

Administrator’s Guide for W80 DECT IP Multi-Cell System

167

Parameter

custom.handset.confirmation_tone.enable

<y0000000000xx>.cfg

Description

It enables or disables the handset to play a tone when a user saves settings or places the handset in
the charger cradle.

Note:

It will take effect on all handsets that are registered on the same system. It works only if “stat-

ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.

Permitted
Values

-1

-Do not modify the handset configuration (Keep the original configuration of the handset).

-Disabled

-Enabled

Default

-1

Supported
Devices

W59R, W53H, W56H, CP930W

Handset UI

W59R/W56H/W53H

OK > Settings > Audio > Advisory Tones > Confirmation

CP930W

Menu > Settings > Basic Settings > Sound > Confirmation

Parameter

custom.handset.low_battery_tone.enable

<y0000000000xx>.cfg

Description

It enables or disables the handset to play a tone when battery capacity is low.

Note

: It will take effect on all handsets that are registered on the same system. It works only if “stat-

ic.auto_provision.handset_configured.enable” is set to 1 (Enabled) and the silent mode is off.

Permitted
Values

-1

-Do not modify the handset configuration (Keep the original configuration of the handset).

-Disabled

-Enabled

Default

-1

Supported
Devices

W59R, W53H, W56H, CP930W

Handset UI

W59R/W56H/W53H

OK > Settings > Audio > Advisory Tones > Low Battery

CP930W

Menu > Settings > Basic Settings > Sound > Low Battery

Shortcut Customization

Shortcuts allow you to quickly and directly access the feature without scrolling through the menu when the phone is
idle. You can customize six shortcuts on the handset in total.

It is only applicable to W59R/W56H/W53H.

Topics

Shortcut Customization Configuration

Shortcut Customization Configuration

The following table lists the parameters you can use to customize the key function on the idle screen.

Parameter

custom.handset.defined_left_key.type

custom.handset.defined_right_key.type

<y0000000000xx>.cfg

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands