Yealink W80 Administrator'S Manual Download Page 83

Page: 83 / 260

Administrator’s Guide for W80 DECT IP Multi-Cell System

Item

Description

Call Time

Time when the call was established.

Handset

Handset which has an abnormal call.

Account

Account number for the current handset.

Call Type

Call type, including

Placed Calls

Received Calls

, and

Missed Calls

Duration

Call duration.

Base Handover

Base received a handover during the call.

Codec

SIP codec used for the call negotiation.

Remote User

Far-site information of the call.

Status

Final state of the call.

Reason

Reason why the abnormality occurs during the call.

OTA upgrading

Not found

Not in range

Unknown:

Packet Loss Rate

Packet loss rate of the call.

Note

: This function is not supported for the time being, it is displayed as "—".

Viewing Abnormal Calls Statistics

Procedure

Access the web user interface of the DM.

Go to

Statistics

Abnormal Calls

Select the desired call type from the

Call Type

drop-down menu.

You can do the following:

Select the search type and enter the search criteria to perform a search.

Click

to customize the properties displayed in the statistics table.

Click

Export

to export statistics.

Click

Reset

to clear and restart the statistics.

Click

Refresh

to refresh the current statistics.

Related Topics

Abnormal Calls Statistics

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands