Yealink W80 Administrator'S Manual Download Page 62 | Manualshive

Page: 62 / 260

background image

Network Configurations

59

Web UI

Network > Advanced > VLAN > WAN Port > VID (1-4094)

Parameter

static.network.vlan.internet_port_priority

[1]

<y0000000000xx>.cfg

Description

It configures the VLAN priority for the Internet port.

7 is the highest priority, 0 is the lowest priority.

Note

: It works only if “static.network.vlan.internet_port_enable” is set to 1 (Enabled).

Permitted
Values

Integer from 0 to 7

Default

0

Web UI

Network > Advanced > VLAN > WAN Port > Priority

[1]

If you change this parameter, the phone will reboot to make the change take effect.

DHCP VLAN Configuration

When the VLAN discovery method is set to DHCP, the phone examines the DHCP option for a valid VLAN ID. You
can customize the DHCP option used to request the VLAN ID.

The following table lists the parameters you can use to configure DHCP VLAN discovery.

Parameter

static.network.vlan.dhcp_enable

[1]

<y0000000000xx>.cfg

Description

It enables or disables the DHCP VLAN discovery feature.

Permitted
Values

0

-Disabled

1

-Enabled

Default

1

Web UI

Network > Advanced > VLAN > DHCP VLAN > Active

Parameter

static.network.vlan.dhcp_option

[1]

<y0000000000xx>.cfg

Description

It configures the DHCP option from which the phone will obtain the VLAN settings.

Multiple DHCP options (at most five) are separated by commas.

Permitted
Values

Integer from 1 to 255

Default

132

Web UI

Network > Advanced > VLAN > DHCP VLAN > Option (1-255)

[1]

If you change this parameter, the phone will reboot to make the change take effect.

VLAN Change Configuration

The following table lists the parameter you can use to configure the VLAN change.

Parameter

static.network.vlan.vlan_change.enable

[1]

<y0000000000xx>.cfg

Description

It enables or disables the phone to obtain VLAN ID using lower preference of VLAN assignment
method, or to close the VLAN feature when the phone cannot obtain VLAN ID.

The priority of each method is LLDP/CDP > Manual > DHCP VLAN.

Permitted
Values

0

-Disabled

1

-Enabled, the phone attempts to use the lower priority method when failing to obtain the VLAN ID

using higher priority method. If all the methods are attempted, the phone will disable VLAN feature.

«
...
60
61
62
63
64
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: Hanlong Pages: 26

SP5050 - Bluetooth hands-free Speakerphone

Brand: Jabra Pages: 221

Brand: Jabra Pages: 22

Brand: Jabra Pages: 42

Brand: Panasonic Pages: 10

Brand: Panasonic Pages: 76

Brand: Panasonic Pages: 36

Brand: Yealink Pages: 48

Brand: Yealink Pages: 2

T46S Skype for Business

Brand: Yealink Pages: 3

Brand: YAKOYA Pages: 25

XDECT 8315 Series

Brand: Uniden Pages: 44

Brand: Yealink Pages: 3

Brand: AUDIOLINE Pages: 124

Brand: Raider Pages: 106

EVITA Telephone

Brand: Topcom Pages: 8

Brand: Doro Pages: 72

Brand: Wheelock Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands