Yealink W80 Administrator'S Manual Download Page 31

Page: 31 / 260

Administrator’s Guide for W80 DECT IP Multi-Cell System

Permitted
Values

String within 64 characters

Default

Blank

Web UI

Base Station > Base Station Settings > Edit > IP Address

Parameter

static.station.X.network.mask

[1]

<y0000000000xx>.cfg

Description

It configures the IPv4 subnet mask.

Note

: It works only if "static.station.X.network.type" is set to 2 (Static IP).

Permitted
Values

String within 64 characters

Default

Blank

Web UI

Base Station > Base Station Settings > Edit > Subnet Mask

Parameter

static.station.X.network.gateway

[1]

<y0000000000xx>.cfg

Description

It configures the IPv4 default gateway.

Note

: It works only if "static.station.X.network.type" is set to 2 (Static IP).

Permitted
Values

String within 64 characters

Default

Blank

Web UI

Base Station > Base Station Settings > Edit > Default Gateway

[1]

X is the registration location ID. X=1-30.

Managing the Connected Base Stations

You can edit the data for a base station or manage a base station that is already registered to the DM.

You can customize the following information of the connected base stations:

Item

Description

Base Station

Name of the base station. When added to the list,

Base Station X

(X ranges from 1 to 30) is used

as the name.

RPN

Radio Fixed Part Number. The base station identity allocated by the DECT system.

Note

: This cannot be edited.

Cluster

Number of the cluster to which the base station belongs.

Sync Level

Sync level within the sync hierarchy.

Status

Synchronization status of the base station.

•

Offline

: not available.

•

Deactive

: available but not activated.

•

Active

: activated but not synchronized.

•

Active and synced

: activated and synchronized.

Active

Activates or deactivates the base station.

Note

: A base station must be active to manage calls of the connected handsets. If it is deac-

tivated, it will no longer connect handsets but it still stays in the list of connected base stations.

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands