Yealink W80 Administrator'S Manual Download Page 57

Page: 57 / 260

Administrator’s Guide for W80 DECT IP Multi-Cell System

Note

: It works only if "static.network.internet_port.type" is set to 2 (Static IP).

Permitted
Values

Subnet Mask

Default

Blank

Web UI

Network > Basic > IPv4 Config > Configuration Type (Static IP) > Subnet Mask

Parameter

static.network.internet_port.gateway

[1]

<y0000000000xx>.cfg

Description

It configures the IPv4 default gateway.

Note

: It works only if "static.network.internet_port.type" is set to 2 (Static IP).

Permitted
Values

IPv4 Address

Default

Blank

Phone UI

Settings > Advanced Settings (default password: admin) > Network > WAN Port > IPv4 > Type (Static
IP) > Gateway

Parameter

static.network.static_dns_enable

[1]

<y0000000000xx>.cfg

Description

It triggers the static DNS feature to on or off.

Note

: It works only if “static.network.internet_port.type” is set to 0 (DHCP).

Permitted
Values

-Off, the phone will use the IPv4 DNS obtained from DHCP.

-On, the phone will use manually configured static IPv4 DNS.

Default

Web UI

Network > Basic > IPv4 Config > Static DNS

Parameter

static.network.primary_dns

[1]

<y0000000000xx>.cfg

Description

It configures the primary IPv4 DNS server.

Note

: In the DHCP environment, you need to make sure “static.network.static_dns_enable" is set to 1

(On).

Permitted
Values

IPv4 Address

Default

Blank

Web UI

Network > Basic > IPv4 Config > Configuration Type (Static IP)/Configuration Type (DHCP) > Primary
DNS

Parameter

static.network.secondary_dns

[1]

<y0000000000xx>.cfg

Description

It configures the secondary IPv4 DNS server.

Note

: In the DHCP environment, you need to make sure “static.network.static_dns_enable" is set to 1

(On).

Permitted
Values

IPv4 Address

Default

Blank

Web UI

Network > Basic > IPv4 Config > Configuration Type (Static IP)/Configuration Type (DHCP) > Sec-
ondary DNS

[1]

If you change this parameter, the phone will reboot to make the change take effect.

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands