Yealink W80 Administrator'S Manual Download Page 131 | Manualshive

Page: 131 / 260

background image

Audio Features

128

Audio Features

This chapter describes the audio sound quality features and options you can configure for the IP phone.

Topics

Alert Tone
Ringer Device
Tones
Audio Codecs
Packetization Time (PTime)
Early Media
Acoustic Clarity Technology
DTMF

Alert Tone

You can configure the following audio alert for the phone:

l

Voice mail tone: allow the IP phone to play a warning tone when receiving a new voice mail. You can customize
the warning tone or select specialized tone sets (vary from country to country) for your IP phone.

l

Dial tone: allow the IP phone to play a specific dial tone for a specified time.

Topic

Alert Tone Configuration

Alert Tone Configuration

The following table lists the parameters you can use to configure the alert tone.

Parameter

features.call.dialtone_time_out

<y0000000000xx>.cfg

Description

It configures the duration time (in seconds) that a dial tone plays before a call is dropped.

If it is set to 0, the call is not dropped.

Permitted
Values

Integer from 0 to 65535

Default

15

Parameter

features.voice_mail_tone_enable

<y0000000000xx>.cfg

Description

It enables or disables the phone to play a warning tone when it receives a new voice mail.

Note

: It works only if “account.X.display_mwi.enable” is set to 1 (Enabled).

Permitted
Values

0

-Disabled

1

-Enabled

Default

1

Web UI

Features > General Information > Voice Mail Tone

Ringer Device

You can use either or both the speaker and the headset as the ringer devices. You can configure which ringer
device to be used when receiving an incoming call. For example, if the ringer device is set to Headset, ring tone will
be played through your headset.

Topic

«
...
129
130
131
132
133
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: NEC Pages: 6

Univerge SV9100

Brand: NEC Pages: 8

Univerge SV9100

Brand: NEC Pages: 4

Univerge SV9100

Brand: NEC Pages: 9

Univerge SV9100

Brand: NEC Pages: 36

UNIVERGE SL2100

Brand: NEC Pages: 4

Univerge SV9100

Brand: NEC Pages: 5

UNIVERGE SL2100

Brand: NEC Pages: 11

Brand: NEC Pages: 256

Brand: NEC Pages: 30

Brand: NEC Pages: 5

Univerge SV9100

Brand: NEC Pages: 3

Univerge SV9100

Brand: NEC Pages: 4

UNIVERGE UM8700

Brand: NEC Pages: 2

EXAI8580 - EXAI 8580 Cordless Phone

Brand: Uniden Pages: 20

Brand: Uniden Pages: 12

Brand: Uniden Pages: 52

Brand: Uniden Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands