Yealink W80 Administrator'S Manual Download Page 101

Page: 101 / 260

Phone Provisioning

Note

: It works only if the protocol type is not defined in the access URL of the provisioning server con-

figured by the parameter "static.auto_provision.server.url".

Permitted
Values

-http

-https

-ftp

Other values

-tftp

Default

tftp

Parameter

static.auto_provision.user_agent_mac.enable

[1]

<y0000000000xx>.cfg

Description

It enables or disables the phone's MAC address to be included in the User-Agent header of
HTTP/HTTPS request via auto provisioning.

Permitted
Values

-Disabled

-Enabled

Default

[2]

If you change this parameter, the phone will reboot to make the change take effect.

Supported Provisioning Server Discovery Methods

After the phone has established network settings, it must discover a provisioning server to obtain software updates
and configuration settings.

The IP phone supports the following methods to discover the provisioning server address:

PnP

: PnP feature allows the phones to discover the provisioning server address by broadcasting the PnP

SUBSCRIBE message during startup.

DHCP

: DHCP option can be used to provide the address or URL of the provisioning server to phones. When the

IP phone requests an IP address using the DHCP protocol, the resulting response may contain option 66 (for
IPv4) or the custom option (if configured) that contains the provisioning server address.

Static

: You can manually configure the server address via the handset user interface or web user interface.

Topics

PnP Provision Configuration
DHCP Provision Configuration
Static Provision Configuration

PnP Provision Configuration

The following table lists the parameter you can use to configure PnP provision.

Parameter

static.auto_provision.pnp_enable

<y0000000000xx>.cfg

Description

It triggers the Plug and Play (PnP) feature to on or off.

Permitted
Values

-Off

-On, the phone broadcasts SIP SUBSCRIBE messages to obtain a provisioning server URL where

the phone can request the configuration from during startup.

Default

Web UI

Settings > Auto Provision > PNP Active

DHCP Provision Configuration

The following table lists the parameters you can use to configure the DHCP provision.

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands