Yealink W80 Administrator'S Manual Download Page 213

Page: 213 / 260

Administrator’s Guide for W80 DECT IP Multi-Cell System

210

Default

3600

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > MWI Subscription Period (Seconds)

Parameter

account.X.sub_fail_retry_interval

[1]

<MAC>.cfg

Description

It configures the interval (in seconds) for the phone to retry to re-subscribe when subscription fails.

Permitted
Values

Integer from 0 to 3600

Default

Parameter

account.X.subscribe_mwi_to_vm

[1]

<MAC>.cfg

Description

It enables or disables the phone to subscribe to the message waiting indicator for the voice mail num-
ber.

Note

: It works only if “account.X.subscribe_mwi” is set to 1 (Enabled) and “voice_mail.number.X” is

configured.

Permitted
Values

-Disabled, the phone will subscribe to the message waiting indicator to a specific account.

-Enabled

Default

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > Subscribe MWI to Voice Mail

Parameter

voice_mail.number.X

[1]

<MAC>.cfg

Description

It configures the voice mail number.

Permitted
Values

String within 99 characters

Default

Blank

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > Voice Mail

Handset UI

OK > Voice Mail > Set Voice Mail > Number

Parameter

account.X.display_mwi.enable

[1]

<MAC>.cfg

Description

It enables or disables the MWI alert to indicate that you have an unread voice mail message.

Permitted
Values

-Disabled

-Enabled

Default

Web UI

Handset & Account > Handset Registration > Add Handset/Edit > Voice Mail Display

Parameter

features.voice_mail_alert.enable

<y0000000000xx>.cfg

Description

It enables or disables the phone to pop up the message when receiving the same amount of new
voicemails.

Permitted
Values

-Disabled

-Enabled

Default

[1]

X is the account ID. X=1-100.

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands