Yealink W80 Administrator'S Manual Download Page 231

Page: 231 / 260

Administrator’s Guide for W80 DECT IP Multi-Cell System

228

Description

It configures the Ethernet interface Maximum Transmission Unit (MTU) on the phones.

Permitted
Values

Integer from 1280 to 1500

Default

1500

[1]

If you change this parameter, the phone will reboot to make the change take effect.

SIP Settings Parameters

Parameter

account.X.custom_ua

[1]

<MAC>.cfg

Description

It configures the suffix of User-Agent in SIP request messages from the phone.

Permitted
Values

String within 128 characters

Default

Blank

Parameter

account.X.check_cseq.enable

[1]

<MAC>.cfg

Description

It enables or disables the phone to check if the CSeq sequence number in the request is lower than
that in the previous request on the same dialog.

Permitted
Values

-Disabled

-Enabled. If the CSeq sequence number in the request is lower than that in the previous request, the

phone will reject the request.

Default

Parameter

account.X.check_to_tag.enable

[1]

<MAC>.cfg

Description

It enables or disables the phone to check if the To-tag is carried in the To header in renewal request.

Permitted
Values

-Disabled

-Enabled. If the To-tag does not exist, the phone will reject the request.

Default

Parameter

sip.send_response_by_request

<y0000000000xx>.cfg

Description

It configures where the IP phone retrieves the destination address for response. The phone will then
send all SIP response messages to the destination address.

Permitted
Values

-from VIA header in the request message

-from source address of the request message

Default

Parameter

sip.requesturi.e164.addglobalprefix

<y0000000000xx>.cfg

Description

It enables or disables the phone to add a global prefix "+" to the E.164 user parts in SIP: URI.

Permitted
Values

-Disabled

-Enabled, the phone will automatically add a prefix "+" to the number in the E.164 format when you

dial using the SIP URI (for example

[email protected]

Default

Parameter

sip.mac_in_ua

<y0000000000xx>.cfg

Description

It enables or disables the phone to carry the MAC address information in the User-Agent header.

Summary of Contents for W80





































































































































































































































































Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands

Yealink W80, Administrator'S Manual

Search results

Summary of Contents for W80

Reviews:

Related manuals for W80

Brands by name

Popular brands