Yealink W80 Administrator'S Manual Download Page 61 | Manualshive

Page: 61 / 260

background image

Administrator’s Guide for W80 DECT IP Multi-Cell System

58

CDP Configuration

CDP (Cisco Discovery Protocol) allows the phones to receive and/or transmit device-related information from/to dir-
ectly connected devices on the local network.

When CDP feature is enabled on the phones, the phones periodically advertise their own information to the directly
connected CDP-enabled switch. The phones can also receive CDP packets from the connected switch and obtain
their VLAN IDs.

The following table lists the parameters you can use to configure CDP.

Parameter

static.network.cdp.enable

[1]

<y0000000000xx>.cfg

Description

It enables or disables the CDP feature.

Permitted
Values

0

-Disabled

1

-Enabled, the phone attempts to determine its VLAN ID through CDP.

Default

1

Web UI

Network > Advanced > CDP > Active

Parameter

static.network.cdp.packet_interval

[1]

<y0000000000xx>.cfg

Description

It configures the interval (in seconds) that how often the phone sends the CDP request.

Note

: It works only if “static.network.cdp.enable” is set to 1 (Enabled).

Permitted
Values

Integer from 1 to 3600

Default

60

Web UI

Network > Advanced > CDP > Packet Interval (1~3600s)

[1]

If you change this parameter, the phone will reboot to make the change take effect.

Manual VLAN Configuration

You can configure VLAN for the Internet port manually. Before configuring VLAN on the phones, you need to obtain
the VLAN ID from your network administrator.

The following table lists the parameters you can use to configure VLAN manually.

Parameter

static.network.vlan.internet_port_enable

[1]

<y0000000000xx>.cfg

Description

It enables or disables the VLAN for the Internet port.

Permitted
Values

0

-Disabled

1

-Enabled

Default

0

Web UI

Network > Advanced > VLAN > WAN Port > Active

Parameter

static.network.vlan.internet_port_vid

[1]

<y0000000000xx>.cfg

Description

It configures the VLAN ID for the Internet port.

Note

: It works only if “static.network.vlan.internet_port_enable” is set to 1 (Enabled).

Permitted
Values

Integer from 1 to 4094

Default

1

«
...
59
60
61
62
63
...
»

Summary of Contents for W80





































































































































































































































































Reviews:

No comments

Related manuals for W80

Brand: NEC Pages: 4

Opal Series 2006

Brand: Teledex Pages: 4

Brand: Fortinet Pages: 271

Brand: Skil Pages: 10

Brand: Ryobi Pages: 107

Brand: FMUser Pages: 16

Brand: Uniden Pages: 33

Brand: Philips Pages: 1

Brand: Zte Pages: 19

Brand: SpectraLink Pages: 99

Brand: SpectraLink Pages: 81

Brand: Gigaset Pages: 137

Brand: Telstra Pages: 27

Brand: Toshiba Pages: 2

Brand: Toshiba Pages: 2

Strata AirLink DK424

Brand: Toshiba Pages: 8

Strata AirLink DK40i

Brand: Toshiba Pages: 12

Strata Cix DKT2504-DECT

Brand: Toshiba Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands