Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 95 | Manualshive

Page: 95 / 138

background image

RDA 400S

27.06.2011
ver.2

95

5.5

Cleaning

At regular intervals and at the end of the season, check that there is no seed or packaging debris
stuck in the seed hoses or in the seed outlets on the distributor head.

At the same time, check the

function of the tramlining flaps.

Figure 5.13

The turn plate made of plastic (A), which controls the doors, must be cleaned regularly.

Clean the hopper, the rape brush, the feed housing and other components at the end of the season.
Check also that no seed has fallen into the ejector tube and the connecting air hose.

Remember that any seed left within the drill can germinate and clog air and seed hoses. Seed can
also attract small rodents which can damage the drill.

Clean the glass plate at the start of every season.

Run the fan for a while to blow-dry the whole system.

Figure 5.10

Figure 5.11

Figure 5.12

A

«
...
93
94
95
96
97
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Brand: lancer Pages: 12

Brand: FEAS Pages: 72

Brand: jcb Pages: 41

DISHSTAR ADA-SEER

Brand: Jackson Pages: 2

Brand: Jasco Pages: 2

Brand: V-TAC Pages: 13

Brand: Panasonic Pages: 23

Chandler Engineering 1910

Brand: Ametek Pages: 46

Brand: ORORO Pages: 16

RGB-BNTv2 NTV-KIT903

Brand: Nav TV Pages: 6

SourceMeter 2425

Brand: Keithley Pages: 141

Brand: Lithium Grim Pages: 13

SKINGUARD Series

Brand: KAP Medical Pages: 39

Brand: Testboy Pages: 16

PRISM MEDICAL C450

Brand: Handicare Pages: 37

Brand: Eaton Pages: 4

Brand: ParaBody Pages: 5

PowerSurvivor 80E

Brand: Katadyn Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands