Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 74 | Manualshive

Page: 74 / 138

background image

Instructions and settings

74

27.06.2011

ver. 2

3.32.3

Adjusting track width

Figure 3.80

The Rapid drill is usually supplied with the row shutoff and track width specified by the customer.
However, it is possible to change these if necessary:

!

A different track width can be obtained by shifting the feed hoses to the seed coulters.

Example:

A track width of 1.75 m can be increased to 2.0 m by moving the front left and rear

right one step outwards. A track width of 1.5 can be produced by moving the rear left and the fore
right one step inward (Y). For bigger changes in track width, it may be necessary to move the hos-
es inside the hopper instead.

3.32.4

Adjusting row shutoff

Figure 3.81

Tramlining can be done with 1, 2 or 3 row shutoff.

!

The sowing row shutoff can be altered by exchanging the spring under the distributor head for
an operating spring (417772, 417776) or a parking spring (417795) depending on whether
more or less rows are to be shut off.

Table 3.6 Possible track widths

One row shutoff

Two row shutoff

Three row shut-off

C-C 138 cm

C-C 150 cm

-

C-C 163 cm

C-C 175 cm

C-C 163 cm

C-C 188 cm

C-C 200 cm

C-C 188 cm

C-C 213 cm

C-C 225 cm

C-C 213 cm

C-C 238 cm

C-C 250 cm

-

417766, 400 S

417795

«
...
72
73
74
75
76
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Relion 670 series

Brand: ABB Pages: 66

Brand: MacDon Pages: 84

Brand: MacDon Pages: 89

Brand: Patton electronics Pages: 18

Brand: Abbott Pages: 2

FreeStyle Libre

Brand: Abbott Pages: 3

Brand: abc Pages: 8

Brand: M-system Pages: 2

Brand: Rico Pages: 34

TRAKTOR KONTROL S4

Brand: Native Instruments Pages: 86

Brand: Native Instruments Pages: 245

Brand: Lafayette Pages: 10

Brand: WARPP Pages: 28

Brand: Safco Pages: 2

VLR100 LED Series

Brand: WE-EF Pages: 3

Brand: Aspect Medical Systems Pages: 104

Brand: Hupfer Pages: 153

KONTROL KUBE ABACUS

Brand: FIBERLOCK Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands