Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 78

Page: 78 / 138

Instructions and settings

27.06.2011

ver. 2

3.35 Maintenance of hydraulic brake system

3.35.1

Maintenance at the start of the season

Figure 3.85

1 Adjust the brake pads. Screw the adjustment screw (A) clockwise while rotating the wheels

slowly. Turn the adjustment screw until you feel resistance in the wheels as they rotate. This
means that the brake pads are in gentle contact with the brake drums.

When the adjustment screw is turned clockwise, the distance between the brake pads and the
brake drums decreases.

When the adjustment screw is turned counterclockwise, the distance between the brake pads
and the brake drums increases.

2 Check that all lines, hoses and brake cylinders are undamaged and that they are not leaking.

3.35.2

Replacing brake components

The brake system’s wheel cylinders, brake pads and brake drums are wearing parts.

NOTE!

The brake pads must not be replaced individually. All the brake pads must be replaced si-

multaneously. The same applies when replacing the wheel cylinders, which must also all be re-
placed at the same time.

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands