Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 22

Page: 22 / 138

Instructions and settings

27.06.2011

ver. 2

3.3.2

Unhitching

Figure 3.9

1 Park the machine on a firm surface.

2 Depressurize the hydraulic system.

3 Disconnect the drill from the tractor lifting arms.

4 Disconnect the hydraulic hoses and electrical cables. Fold back and secure the hose holders in

the upright position.

NOTE!

If unhitching is done on soft ground, be sure to fit the yellow locking device on the lifting

ram prior to depressurizing the system. See ”

3.16 Locking the lifting rams during service” on page

3.4

Connecting the hydraulic hoses and electrical cables

3.4.1

Connection of the hydraulic hoses for operating the machine

1 The two hoses marked by yellow plastic rings are used to raise and lower the seed drill and to

operate the bout markers.

2 The two hoses marked by white plastic rings are used to fold down the side sections and to ad-

just the Crossboard.

3 The two hoses marked by blue plastic rings are used to operate the pre-implement.

4 The two hoses running to the hydraulic top rod (optional equipment) should be connected to a

two-way hydraulic connector.

Carefully check that all hoses are connected in pairs to the correct hydraulic couplings on the
tractor.

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands