Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 54

Page: 54 / 138

Instructions and settings

27.06.2011

ver. 2

3.27.2

Filling from small sacks

NOTE!

Pay attention to safety. Do not walk under a suspended load! Make sure there is nobody on

the drill when feeding the seed. Make sure there is nobody on the hopper. Avoid contact with and
inhalation of seed disinfectant.

Figure 3.64

NOTE!

The stepping boards and platform of the drill are not designed for manual loading from

small seed bags.

Filling should preferably be done using a loader and the bags placed on a pallet.

Lift the pallet diagonally from the front right, with the tractor turned away to the side, up to the
guard rail level in order that one can safely access the platform.

3.28 Emptying the seed hopper

Figure 3.65

The hopper can be emptied by a single action. Remove the sliding hatch completely. If emptying
a bit at a time, slide the hatch up gradually.

Do not forget to replace the hatch after emptying.

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands