Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 87

Page: 87 / 138

RDA 400S

27.06.2011
ver.2

4.5

Intermediate packer

The intermediate packer should be in the lowered position when pulled in the furrow as well as on
the headland.

Always lift the intermediate packer

when reversing the seed drill

. If the packer is not lifted, the

wheel undercarriage and the wheels themselves could be damaged.

When transporting the seed drill

by road, the intermediate packer must always be raised

. This

will avoid unnecessary tyre wear.

The intermediate packer scrapers must be adjusted in accordance with ”

3.18 Scraper” on page 42

Figure 4.5

Figure 4.6

Figure 4.7

Figure 4.8

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands