Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 50

Page: 50 / 138

Instructions and settings

27.06.2011

ver. 2

Figure 3.57

10 Keep

on the Control Station or the remote control depressed until a suitable seed amount

has been filled into the bag. Pulses from the seed boxes are counted up in menu row 3.

Figure 3.58

11 Weigh the content of the bag. Scroll down to menu row 4, mark it using

and enter the

value in kg. Confirm with

The number of pulses per kilogram is automatically counted up on menu row 5, while menu
row 6 will be marked.

To manually enter the number of pulses per kg, scroll back to row 5 and use

to mark it.

Manually enter the value and confirm with

12 Confirm completed calibration on menu row 6, “Accept”, by depressing

To interrupt the calibration and repeat it from the beginning, scroll to menu row 7 “Cancel”

and depress

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands