Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 117

Page: 117 / 138

RDA 400S

27.06.2011
ver.2

117

The area meter/speedometer

has no indication or an incorrect

indication!

- Has the Control Station been programmed with the

correct number of pulses per metre? See ”

3.30.3 Pro-

gramming” on page 63

If the value in the area/speed field is too low, then re-
duce the number of pulses per metre.

If the value in the area/speed field is too high, then in-
crease the number of pulses per metre.

The tramline doors seize!

- Are the doors blocked or wedged up due to seed or

rubbish?

In this case dismantle the glass cover on the distribu-
tor head and clean.

The drilling depth of the centre

and side section differs!

- Check whether the long ram rod of the folding ram is

completely extended and that the rod does not slowly
retract during driving.

- Check the setting on the wing sections, see

”3.11 Ad-

justing the wing sections” on page 34.

- Check the adjustment of the cranks on the wing sec-

tions, see

”3.9 Mechanical adjustment of sowing

depth” on page 30.

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands