Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 61

Page: 61 / 138

RDA 400S

27.06.2011
ver.2

Shut-off of seed feeding

Feeding can be shut off by depressing the button

(18) on the left side. The indicator lamp

shows the seed feeding has been shut off.

Electric adjustment of sown seed amount (only applies for hydraulic feed

output)

The default value and percentage change are recorded in the calibration menu.

The electric adjustment of sown seed amount can be controlled using the

but-

tons.

results in an increase in the sown amount according to the calibration selections, while

reduces the sown amount according to the calibration selections, and

results in the

default value. (Max. 5 steps and max. up/down of +/- 99%.)

Calibration (only applies to hydraulic feed output)

Depress the

button to call up the calibration menu. See “Figure 3.69”. Proceed as explained

in ”

3.26 Calibration” on page 48

Figure 3.69

Alarm

The red indicator lamp in the alarm symbol (21) lights and the buzzer sounds. (The signal can be
deselected in the programming menu. See ”

3.30.3 Programming” on page 63

(!) is displayed. Several (!) indicate more than one alarm condition. Press

for an explana-

tion of the alarm in the display. Press

to acknowledge the alarm.

When the main switch is switched on, a number of alarm indications appear in the display and the

buzzer sounds. Press

to acknowledge the alarm. The alarm disappears when drilling starts

and all functions are OK.

It is possible to acknowledge several alarm conditions at the same time. Press

and then

press

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands