Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 46 | Manualshive

Page: 46 / 138

background image

Instructions and settings

46

27.06.2011

ver. 2

3.24 Adjusting the air-flow

3.24.1

Hydraulic fan "Fenix"

The air volume is adjusted using the fan speed.

The fan speed can be adjusted in various ways, depending on the tractor on which it is mounted:

A

The fan is controlled using the tractor’s flow valve. A flow valve is available on most tractors
with a constant pressure hydraulic system. If the tractor has a priority hydaulic connector, be
sure to use this. Control of the hydraulic pressure from the tractor’s hydraulic system will then
be optimized for the hydraulic fan and on the tractor. Before installing an external valve ac-
cording to alternative (b) or (c), check whether a flow valve is optionally available for the trac-
tor’s hydraulic system.

Figure 3.49

B

If the tractor is equipped with a constant pressure hydraulic system but no flow valve, the fan
speed is instead controlled with a check valve installed on the pressure line between the tractor
and the sowing machine. The check valve can be ordered as already fitted or can be fitted on
models without this valve (part no. 420160).

C

If the tractor has a constant pressure system, the fan rpm can be adjusted using an additional
rpm regulator placed between the hydraulic hoses of the tractor and drill or on the fan holder.
The optional speed regulator can be ordered fitted or can be fitted later (part no. 420154).

Use the fan rpm as indicated in the table below. Check the fan rpm in the Control Station display.

The low rpm alarm on the Control Station should ideally be programmed to 300 rpm below the
set rpm while the high rpm alarm should be set 300 rpm above the set rpm. See ”

3.30.3 Program-

ming” on page 63

.

Figure 3.50

Figure 3.51

Table 3.2 Recommended fan speed

RDA 400 S

Small seeds

3000 rpm

Corn

3600 rpm

-

+

«
...
44
45
46
47
48
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Brand: NARGESA Pages: 50

Brand: TC Electronic Pages: 2

Brand: Bahco Pages: 131

Brand: Bahco Pages: 126

Brand: Garmin Pages: 10

Brand: Naviom Pages: 31

Brand: Haag-Streit Pages: 18

Brand: Haag-Streit Pages: 20

Brand: V-TEK Pages: 2

Brand: V-TEK Pages: 112

RIDA qLine ZG2601

Brand: R-Biopharm Pages: 23

LED Street Bar 16x3W RGB IP65

Brand: Varytec Pages: 9

Brand: VARILITE Pages: 8

EVENTPROFILE VL800

Brand: Vari Lite Pages: 34

Optica 30 Series

Brand: Varex Imaging Pages: 36

Brand: Vatech Pages: 137

Brand: Vatech Pages: 68

Brand: Varytec Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands