Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 17 | Manualshive

Page: 17 / 138

background image

RDA 400S

27.06.2011
ver.2

17

2

Installation instructions

2.1

Installation of the Control Station on the tractor

1 Be sure to install the control box securely in the tractor cab. Place the control box within the

field of vision while looking in the travelling direction. Install the bracket as shown in the il-
lustration.

NOTE!

Check for hidden cables before drilling holes in the tractor cab.

2 Connect the Control Station to the electrical socket on the tractor. If an electrical power outlet

is not available, extra wiring must be installed. Preferably use 6 mm² cable. Connect the cables:
Brown to positive (+) and blue to earth (-).

NOTE!

The polarity must not be reversed.

It is important to have good wiring connections, as a loose connection will prevent correct opera-
tion.

Do not use a cigarette lighter outlet,

as the current consumption is up to 20 A.

Make sure that the connecting cable to the drill is not trapped under the rear window of the tractor
as this may cause damage. Use a hatch or a hole. Securely clamp the cable in the tractor cab. This
protects the Control Station from damage in case the connection cable has inadvertently not been
disconnected prior to unhitching the drill.

Figure 2.1

Figure 2.2

«
...
15
16
17
18
19
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Brand: ParaBody Pages: 4

Brand: Cadman Pages: 66

Brand: Kawai Pages: 10

Frontier FC5706

Brand: OHAUS Pages: 47

Brand: Ocutech Pages: 4

Brand: quadient Pages: 14

Brand: Qu-Bit Electronix Pages: 31

Brand: Fast Pages: 60

Brand: MacDon Pages: 238

Brand: Jefferson Pages: 2

Brand: Lighthouse Pages: 2

MS-1 MICRO SEQUENCER - MUSICIAN S GUIDE

Brand: Kurzweil Pages: 91

Brand: schmersal Pages: 20

Brand: KaVo Pages: 70

Brand: GreenTec Pages: 66

Brand: Slick Pages: 2

Sedeo Lite Q700M

Brand: Quickie Pages: 9

Brand: Global Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands