Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 92 | Manualshive

Page: 92 / 138

background image

Maintenance and service

92

27.06.2011

ver. 2

5.1

General maintenance

Figure 5.5

A machine is only as good as the service it receives!

Before starting work, check that all nuts and screws are tightened. During the season, check the
tightness of nuts and screws regularly, as well as the wear on linkages and the hydraulic ram
mountings.

NOTE!

The screws holding links should not be tightened so much that movement in the linkage is

restricted.

NOTE!

When cleaning the drilling system or when servicing the transmission system on machines

with hydraulic feed output, the hydraulic flow to the fan and feed output driving mechanism must
always be shut off beforehand.

The hydraulic system does not normally require any maintenance, but check that the hoses and
couplings are undamaged.

NOTE!

Dirt must be kept out of the hydraulic system during any service work. Wipe with clean

paper or a clean rag. Lay the parts on a clean surface (not directly on the work bench). Rinse off
parts with e.g. a degreasing compound before fitting them.

Always grease the piston rods after cleaning them or if the drill is not going to be used for a long
time.

Grease galvanized and chromium plated surfaces before long periods of storage.

To maintain the quality of this seed drill, always use Väderstad original spare

parts.

«
...
90
91
92
93
94
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Brand: Olympus Pages: 86

Brand: Rath Pages: 3

Brand: FENDT Pages: 31

Litmann Quality 3100

Brand: 3M Pages: 2

Brand: Raven Pages: 17

Brand: Campbell Pages: 12

Brand: HABYS Pages: 16

Brand: IDEAL Networks Pages: 60

Brand: IceCure Pages: 104

Brand: UNI-T Pages: 4

UPO3000E Series

Brand: UNI-T Pages: 94

Brand: Underhill Pages: 12

Brand: UMS Pages: 92

Brand: uniprox Pages: 3

Brand: MAGSTIM Pages: 86

Brand: neofeu Pages: 28

Brand: Walimex Pro Pages: 44

Brand: Otto Bock Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands