Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 43 | Manualshive

Page: 43 / 138

background image

RDA 400S

27.06.2011
ver.2

43

3.19 Bout marker adjustment

Figure 3.43

Adjust the bout markers as shown in “Figure 3.43”. This adjustment is approximate. To avoid dou-
ble-seeding or non-seeding, which may occur if the driver sits at an angle in the tractor, a follow-
up check should be done in the field. Depending on the type of tractor and the driver position, the
marking scraper may be observed differently. The marking scraper should be adjusted after about
an hour’s time of operation.

3.20 Track eradicators, tines (option)

Figure 3.44

Track eradicators can be mounted in the frame tubing at the front of the pre-implements.

Track eradicators should only be used on drills equipped with an intermediate packer. This is be-
cause the intermediate packer needs to be lifted with the tractor's hydraulic lifting arms at the
headland to enable sufficient clearance of the track eradicator tines.

The working depth of the track eradicators can be set by manually repositioning the tines in the
hole series mountings.

For road transport, turn the track eradicator tines upside down in their mountings.

RDA 400: 4,0 m

«
...
41
42
43
44
45
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Brand: ZOLL Pages: 344

Brand: ABB Pages: 9

Brand: Makita Pages: 84

Brand: HAMAR LASER Pages: 49

Brand: Quadro Pages: 11

Brand: MADRIX Pages: 12

Brand: Narcotrend Pages: 47

Brand: Echo Pages: 6

Pro Attachment Series

Brand: Echo Pages: 28

Brand: Echo Pages: 2

Pro Vantage 12+ Series

Brand: Ecco Pages: 6

Brand: Gainsborough Pages: 2

Brand: Gainsborough Pages: 2

Brand: Gait up Pages: 12

Brand: Gait up Pages: 6

Brand: Gaiam Pages: 2

ENET-232 Series

Brand: National Instruments Pages: 105

Brand: Xtool Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands