Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 82

Page: 82 / 138

Instructions and settings

27.06.2011

ver. 2

3.37 Maintenance of pneumatic brake system

3.37.1

Maintenance at the start of the season

Figure 3.90

1 Adjust the brake pads. Screw the adjustment screw (A) clockwise while rotating the wheels

slowly. Turn the adjustment screw until you feel resistance in the wheels as they rotate. This
means that the brake pads are in gentle contact with the brake drums.

When the adjustment screw is turned clockwise, the distance between the brake pads and the
brake drums decreases.

When the adjustment screw is turned counterclockwise, the distance between the brake pads
and the brake drums increases.

2 Check the oil level. Top up with new oil if necessary. Only use mineral oil type GL-4 or equiv-

alent.

NOTE!

The mineral oil should be type GL-4 or equivalent. Other types of brake fluid will damage

the system’s seals.

3 Check that all lines, hoses and brake cylinders are undamaged and that they are not leaking.

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands