Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 70

Page: 70 / 138

Instructions and settings

27.06.2011

ver. 2

3.31.4

Ultrasonic transmitter

Figure 3.75

The distance (A) between the ultrasonic transmitter and the plate at maximum raised position
should be max. 500 mm.

If work needs to be performed close to the ultrasonic transmitter and there is a risk that the ultra-

sonic ray may be interrupted, the Control Station must be blocked beforehand with the

(“STOP”) and

buttons. Otherwise there is a risk that tramlining advances or that seed output

commences.

3.31.5

Master ram stop bolt

Figure 3.76

If desired, the drilling depth can be manually set. Change the position of the stop bolt (B) on the
master ram to the desired position.

When using the Control function, it is recommended to set the stop bolt to a “safe drilling depth”,
i.e. the maximum desired drilling depth.

If a problem should occur with the Control function, the manually set drilling depth can be used
to enable continued drilling.

3.31.6

Parking

When parking the machine, especially on soft ground, the stop bolt should be moved upwards on
the ram to relieve the hydraulic system of the load.

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands