Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 63

Page: 63 / 138

RDA 400S

27.06.2011
ver.2

3.30.3

Programming

The Control Station has been preset at the Väderstad factory depending on the type and size of the
machine it is supplied with. The Control Station settings need to be reentered after replacement or
a reset.

It is also possible to use the settings to adjust e.g., alarm delays, area metering, etc.

To enter the programming menu, keep

pressed while simultaneously switching on the pow-

er switch (1).

If the Control Station already has been switched on, switch to the programming menu by keeping

the button

depressed for 5 seconds. To complete programming and return to the drive

mode, select the last menu in the scroll list:

. Confirm with

Use the selection dial to select the desired menu. Selections are shown against a dark background.

Use

to confirm a selection and then select or change the value of the selected item. Confirm

the value/selection with

Menus:

Language. Select the desired language for alarm texts, etc.

Machine type. Select “RDA 400 S”.

Hydraulic feeding, Yes/No.

GPS, Yes/no. See ”

3.30.6 GPS (Global Positioning System)” on page 66

Number of pulses per revolution generated by the seed box drive sensor. Default setting:

360.

Serial number. Record the serial number of the machine here. Select digits with the dial

and advance using

Machine width. Set the machine width here: 4.0 m.

Manual start. Select the intended drive speed here by keeping the button

de-

pressed. (Starting of feed output when drilling is commenced from a corner of the field, etc.)

Output stop, Yes/No. Option Default setting: No.

Only if Yes has been selected in

menu 9, Setting of lift time delay. Default setting 0.0 sec.

Radar, Yes/No.

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands