Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 72 | Manualshive

Page: 72 / 138

background image

Instructions and settings

72

27.06.2011

ver. 2

3.32.2

Tramline options

The

RDA 400 S

model is supplied with equipment for centre marking installed.

The drill is supplied having two or three row shutoff. If one row shutoff is required, it can be
achieved by changing the flap springs for the outlets which are not required to tramline, see

”3.32.4 Adjusting row shutoff” on page 74.

For control or alteration of the track width, see

Adjusting track width” on page 74.

The various tramlining widths are set using the Control Station. The selected tramlining pro-
gramme is shown at the lower left of the display, while the current furrow in the sequence is shown
at the lower right part.

Keep the

button depressed until the tramlining programme digit is selected. Then use the

selection dial to set the desired tramline interval and confirm with

. Advance to the desired

start value using

. The lamps (6) light when tramlining is in progress.

Also see ”

3.30.2 Functions” on page 59

.

For successful tramlining, it is important to organise the tracks before starting the work.

Example

: RDA 400 S to be set for 24 m tramlining. Select tramlining programme 6 (24/4=6). Ad-

vance the starting value to 3.

Figure 3.79 Centre marking

Table 3.3 Tramlining options

RDA 400 S centre marking

8, 12, 16, 20, 24 metre

RDA 400 S side marking

16, 24 and 32 metre

RDA 400 S/12 m

RDA 400 S/16 m

RDA 400 S/20 m

«
...
70
71
72
73
74
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Brand: Taurus Pages: 28

Brand: Kärcher Pages: 54

Brand: ABB Pages: 85

Brand: Parker Research Corp Pages: 4

Brand: Eastwood Pages: 20

Brand: Daihan Scientific Pages: 43

Brand: Federal Signal Corporation Pages: 12

Brand: MAGIC FX Pages: 25

Brand: Nel-Tech Labs Pages: 8

Brand: Zimmer Pages: 54

Brand: Zimmer Pages: 4

Brand: Zimmer Biomet Pages: 23

Brand: Zimmer Pages: 16

Brand: Zimmer Pages: 2

Brand: Zimmer Pages: 32

Brand: Zimmer Pages: 96

Brand: Össur Pages: 16

Exoform Dorsal Night Splint

Brand: Össur Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands