Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 76 | Manualshive

Page: 76 / 138

background image

Instructions and settings

76

27.06.2011

ver. 2

3.34 Hydraulic brakes (accessories)

3.34.1

General

The RDA 400 can be fitted with hydraulic brakes. The system also has an emergency brake that
is applied if the machine becomes unhitched from the tractor. The emergency brake system con-
sists of an accumulator, a valve and a wire that is connected to the tractor.

3.34.2

Connection and driving

Figure 3.83

1 Connect the hydraulic hose of the brake system to the brake coupling on the tractor. Please note

that the hose must only be connected to a brake coupling that is controlled by the tractor's brake
pedal and provides a maximum pressure of 150 bar. Attach the wire to a convenient point on
the tractor. Make sure the wire cannot get entangled.

2 Ensure that the emergency brake valve is set to position A.

3 Press down the brake pedal and keep it in this position until the pressure gauge on the ma-

chine's draw-bar shows 120 - 140 bar.

4 The machine is now ready for driving.

1

2

3

4

A

120

140

«
...
74
75
76
77
78
...
»

Summary of Contents for Rapid RDA 400S











































































































































Reviews:

No comments

Related manuals for Rapid RDA 400S

Brand: Baoding Longer Precision Pump Pages: 6

Brand: Valmar Pages: 78

Brand: Valhalla Scientific Pages: 64

Z9 Commercial Collection System Z9A

Brand: Yazoo/Kees Pages: 3

Z9 Commercial Collection System Z9A

Brand: Yazoo/Kees Pages: 36

Brand: YASKAWA Pages: 1166

Brand: Zodiac Pages: 2

Brand: Zipper Mowers Pages: 37

Brand: Zimmer Pages: 46

Brand: Task Force Tips Pages: 16

Brand: +GF+ Pages: 2

Unity for Pro-Flex Pivot

Brand: Össur Pages: 40

ICELOCK 234 LANYARD

Brand: Össur Pages: 94

Brand: Össur Pages: 115

Brand: Össur Pages: 253

Brand: Öhlins Pages: 8

Brand: ?HC Pages: 2

Brand: Posture Pump Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands