Home
/
Task Force Tips
/
VORTEX 2 ER
/
Manual

Task Force Tips VORTEX 2 ER, Manual

Share

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Page: 1 / 16

background image

©Copyright Task Force Tips LLC 2018 - 2019

LIS-045 April 22, 2019 Rev01

MANUAL: VORTEX

®

MONITOR

MOUNTED NOZZLES

INSTRUCTIONS FOR INSTALLATION, SAFE OPERATION AND MAINTENANCE

WARNING

Understand manual before use. Operation of this device without understanding the manual
and receiving proper training is a misuse of this equipment. Obtain safety information at
tft.com/serial-number

This instruction manual is intended to familiarize ﬁ reﬁ ghters and maintenance personnel with the operation, servicing and
safety procedures associated with the VORTEX ﬁ re ﬁ ghting nozzles.
This manual should be kept available to all operating and maintenance personnel.

TASK FORCE TIPS LLC

MADE IN USA • tft.com

3701 Innovation Way, Valparaiso, IN 46383-9327 USA

800-348-2686 • 219-462-6161 • Fax 219-464-7155

VORTEX 2 ER

VORTEX 2

VORTEX 6 ER

1
2
3
...
»

Summary of Contents for VORTEX 2 ER

















Reviews:

No comments

Related manuals for VORTEX 2 ER

Brand: 3M ESPE Pages: 50

Brand: YATEK Pages: 72

Brand: E-Pill Pages: 8

XL-7 Command Station

Brand: E-Mu Pages: 22

Brand: Halyard Pages: 88

Brand: Garmin Pages: 2

Brand: Hakko Electronics Pages: 16

Brand: i-CAT Pages: 96

APT-9411 Series

Brand: TAKAYA Pages: 77

Brand: Teac Pages: 44

Brand: Te Pari Pages: 6

Brand: Yamaha Pages: 39

Brand: Yamaha Pages: 110

Brand: OttLite Pages: 2

Brand: Rohde & Schwarz Pages: 36

MicroVention MCS-18

Brand: Terumo Pages: 104

Brand: HABYS Pages: 20

Brand: Advanced Bionics Pages: 172

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands