Vaderstad Rapid RDA 400S Original Instructions Manual Download Page 79

Page: 79 / 138

RDA 400S

27.06.2011
ver.2

3.36 Pneumatic brakes (accessories)

The RDA 400 can be fitted with pneumatic brakes.

3.36.1

Use while driving

1 Connect the lines to the tractor’s couplings.

The compressed air line has a red mounting and must be connected to the red coupling.

The control line has a yellow mounting and must be connected to the yellow coupling.

Figure 3.86

2 Adjust the compressed air valve’s tap (A) according to the machine’s load as below:

Driving with empty seed hopper:

The tap must be in the horizontal position.

An incorrectly set tap entails a risk of the seed drill’s wheels locking during braking. This can
cause you to lose control of the machine.

Driving with full seed hopper:

The tap must be in the vertical position.

An incorrectly set tap entails a risk of there being insufficient braking force.

Summary of Contents for Rapid RDA 400S











































































































































Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands

Vaderstad Rapid RDA 400S, Original Instructions Manual

Search results

Summary of Contents for Rapid RDA 400S

Reviews:

Related manuals for Rapid RDA 400S

Brands by name

Popular brands